Search Results

Standard

Specifications for Low Carbon Cast Steel Shot

2015-06-18

HISTORICAL

J2175_201506

This SAE Recommended Practice describes chemical analysis, hardness, microstructure, and physical characteristic requirements for low carbon cast steel shot to be used for shot peening or blast cleaning operations.

Standard

Medical Device Shot Peening

2014-05-07

CURRENT

J3020_201405

This SAE Standard and its supplementary detail specifications cover the engineering requirements for the controlled shot peening of a medical device where shot peening is required for enhancement of a material's mechanical properties through the intentional creation of compressive residual stress.

Standard

High-Carbon Cast-Steel Shot

2013-10-16

HISTORICAL

J827_201310

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

Cut Wire Shot

2013-10-16

HISTORICAL

J441_201310

This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.

Standard

High-Carbon Cast-Steel Grit

2013-10-16

HISTORICAL

J1993_201310

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

Standard

Metallic Shot and Grit Mechanical Testing

2013-08-21

HISTORICAL

J445_201308

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

Shot Peening Coverage Determination

2013-04-24

HISTORICAL

J2277_201304

This SAE recommended practice provides some procedure for determining shot peening coverage and relating coverage to part exposure to the media stream. Effectiveness of shot peening is directly dependent on coverage. Either incomplete or excessive coverage can be detrimental to fatigue strength and life.

Standard

Test Strip, Holder, and Gage for Shot Peening

2013-02-18

HISTORICAL

J442_201302

This SAE standard defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. Guidelines for use of these items can be found in SAE J443 and SAE J2597.

Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning

2012-09-17

HISTORICAL

J444_201209

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.

Standard

Procedures for Using Standard Shot Peening Almen Strip

2010-06-16

HISTORICAL

J443_201006

This SAE Recommended Practice provides uniform procedures for using the standard shot peening Almen strips reported in SAE J442. Standard Almen strips are used to establish saturation, determine intensity, monitor repeatability of the shot peening machine operations, and can be used to predict a desired result on a part. It is recommended that the standard Almen strip A be used for intensities that produce arc heights of 0.10 mm A (0.004 in A) to 0.60 mm A (0.024 in A). For intensities below 0.10 mm A (0.004 in A), the standard N strip is recommended, and for intensities above 0.60 mm A (0.024 in A), the standard C strip is recommended. Use of SAE 2597 Computer Generated Shot Peening Saturation Curves is voluntary, existing shot peening processes that do not take advantage of computer generated saturation curves need not be changed to meet the requirements listed herein.

Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning

2010-06-16

HISTORICAL

J444_201006

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.

Standard

Computer Generated Shot Peening Saturation Curves

2010-01-14

HISTORICAL

J2597_201001

This SAE Recommended Practice defines a procedure for the use of computer generated saturation curves to determine peening intensity. Calculation of intensity within a tolerance band for each data set in Table 1 one is required for compliance with this practice.

Standard

Cut Wire Shot

2009-11-09

HISTORICAL

J441_200911

This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.

Standard

Shot Peening Coverage Determination

2009-10-26

HISTORICAL

J2277_200910

This SAE Recommended Practice provides procedures for determining shot peening coverage. Effectiveness of shot peening is directly dependent on coverage. Inadequate or excessive coverage may be detrimental to fatigue strength and life.

Standard

High-Carbon Cast-Steel Shot

2005-07-25

HISTORICAL

J827_200507

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

Metallic Shot and Grit Mechanical Testing

2005-07-25

HISTORICAL

J445_200507

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

High-Carbon Cast-Steel Grit

2005-07-25

HISTORICAL

J1993_200507

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning

2005-07-25

HISTORICAL

J444_200507

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.

Standard

HIGH-CARBON CAST-STEEL SHOT

1996-09-01

HISTORICAL

J827_199609

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

HIGH-CARBON CAST-STEEL GRIT

1996-09-01

HISTORICAL

J1993_199609

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.